1984 Chevrolet Blazer “Spool Bus”

$25000 – Cloverdale, IN:

“Possible trade for a Plymouth cuda

Spool Bus s10 blazer 8sec truck
70k original miles on the body
Zero rust! Underneath looks factory clean
Street driven all the time. Drove 5 hours to LSfest…. Ran low 9s and drove home.
Makes about 725whp on low boost and went 9.20 at 1.48 with a soft 1.42 60ft. I didn’t get to the track but twice this year to go any faster. That was its second timet the track since the entire build was done. Leaving harder would have gone 8.90s on low boost.

Last i checked it was 28xx lbs without driver.
Should go low 8s to high 7s turned up easy.
Street race magazine featured.
1320 video featured

Truck was professionally wrapped with 3m products. Hood is a brushed aluminim wrap. Its red underneath the wrap if taken off. It has been wet sanded and little paint chips filled. Pretty much ready to spray color and clear if you don’t like the wrap.

6.0 lq4 with callies rods and diamond pistons. One season on fresh motor.
Btr stage 2 turbo cam/ lifters/ springs.
Straub Trunion bushing upgrade
Hardened pushrods.
Ported 317 heads.
Ls9 gaskets.
Headstuds.
Holley hi ram 102mm
Fast big mouth 92mm TB

Holley 12-1800 fuel pump
Holley fuel rails
-10 feed and return PTFE lines
Aeromotive FPR.
210lb bosch injectors
14 gallon aluminim fuel cell braced

Twin s360 turbos with upgraded HD 360 thrusts bearing and seamless seals
Twin tail mvr 42mm Wastegates
Tial 50mm BOV
Morimoto 4 inch intercooler
3 inch aluminim piping insulated wrapped.
Forward facing stainless turbo headers
Cx racing 90 degree mounts

MS3PRO gen 1 engine management
Microsquirt I/O box
Standalone LS plug and play harness.
4bar map sensor
Cherry wheel sensor for traction control
4 port boost controller

RPM lvl 5 4l80 trans
Extreme auto billet manual valve body with billet pro trans brake.
Precision 3600 triple disk
Derale double row trans cooler with fan.
Kilduff machine shifter
Moly yoke on trans and rear diff with 3.5” driveshaft
Safety loop

Strange built 8.8 ford rear
Strange full spool
Moser diff cover with main cap support
Strange 35 spline axels

Willwood 4 piston front and rear dynalight brakes and calipers.
Wilwood manual master and proportion valve.
Stainless brake lines

Heidts mustang 2 super ride front suspensions
Flaming river rack and pinion
Viking crusader double adjustable coilovers
Innovate racecract moly travel limiters.
Drop spindles

Tubular rear mini tub. Ladder bars
Custom cantilever shock setup
Viking crusader double adjustable coilovers

Weld rts front runners
Weld rts 15×12 rears with
325 50 15 et street R tires

Harwood 5 inch fiberglass hood
Aeroquip latches
Roll pan molded in
Chromoly parachute pullbar and tubular bag mount.
Stroud chute and cable kit.
Aftermarket Bumper with fog lights
New headliner

Aluminum dash with autometer gauges and tablet display.
Pioneer amp
Nvx 6×9 and 3.5 speakers
AGM battery
Kirkey seats and covers
Racequip cam lock 6 point harnesses.
10 point moly 8.5 cert cage
Boxed / tube frame
Moly trans mount
Engine plated with torque limiter bars.

Afco radiator
Derale high output fans
Aluminim shroud
160 thermostat. “

Source: https://indianapolis.craigslist.org/cto/d/spool-bus-s10-blazer-8sec/6411204228.html